What does getPermit actually do?

getPermit reads your job details and tells you what a California city expects before you file: which permits the work triggers, the documents and plans you'll need, the fees to budget for, and the common reasons applications in that jurisdiction get bounced back. It produces a clear checklist you can act on. It does not submit to the city for you — you (or your permit person) stay in control of what gets filed.

Is there a human involved, or is it just AI?

Both. The AI does the research and drafts the assessment and checklist; an experienced permit coordinator reviews and approves it before it's treated as authoritative. The human check is the point — it's how we keep it trustworthy in a process where a wrong filing has real consequences.

Which cities do you cover?

We're starting deep in California rather than shallow everywhere. For a city we haven't fully mapped yet, we'll give you accurate general California guidance and point you to that city's official building department — and you can join the waitlist to be notified when we cover it in depth. We will not invent city-specific fees or timelines we haven't verified.

Solo electricians, plumbers, and HVAC contractors, and small general contractors who don't have a dedicated permit department and lose billable hours to permit admin.

How much does it cost?

It's pre-launch. Join the waitlist and you'll get founder pricing, your jurisdiction prioritized, and a direct line to the team. No spam, no credit card.

We're onboarding a first set of California contractors. Join the waitlist with your city and trade so we can prioritize the jurisdictions our early users actually work in.

Mini-split installation permits in Los Angeles, CA

General California guidance last updated August 2, 2026 · Los Angeles data verified May 22, 2026

What HVAC contractors need to know about pulling a mini-split installation permit in Los Angeles (Los Angeles County).

Short answer

In California, installing a ductless mini-split heat pump requires a mechanical permit plus electrical scope for the new dedicated circuit and disconnect — even for a single-zone unit. The work falls under the California Mechanical Code (Title 24, Part 4), the California Electrical Code (Title 24, Part 3), and the Energy Code (Title 24, Part 6). A C-20 (HVAC) licensed contractor generally pulls it.

Los Angeles accepts submittal through the PermitLA + ePlanLA (LADBS online permits) and has adopted the 2025 California Building Code (LA Building Code, LAMC Chapter IX). Fee details and sources are below.

Los Angeles permit data

Sourced from public City of Los Angeles documents — every field carries the source URL and verification date.

Permit portal

PermitLA + ePlanLA (LADBS online permits)

verified May 22, 2026 · source · PermitLA (https://permitla.lacitydbs.org) handles express permits that do not require plan review; ePlanLA (https://eplanla.lacity.org) handles permits that require plan check. Both require a free Angeleno account.

Adopted code edition

2025 California Building Code (LA Building Code, LAMC Chapter IX)

verified May 22, 2026 · source · Per Council File 25-1217 (ordinance amending LAMC Chapter IX, December 2025); LA adopts the 2025 California Building Code and 2025 California Residential Code with local amendments

Fee schedule

LADBS Fee Schedules — building permit valuation table, plan check fees, and per-trade fee tables

verified May 22, 2026 · source

Los Angeles Department of Building and Safety (LADBS) →All verified Los Angeles data →

The general picture in California

Cities treat a mini-split like any other permanent HVAC installation: mechanical scope for the refrigerant lines, mounting, and condensate under the California Mechanical Code, and electrical scope for the dedicated circuit and outdoor disconnect under the California Electrical Code. The electrical half is the part that gets underestimated — a "simple" single-zone install still means a new circuit from the panel, a disconnect at the condenser, and sometimes a load calculation on an older service. The Energy Code touches the job too: ductless equipment sidesteps duct testing, but compliance paperwork can still be required, and the unit must meet current federal SEER2/HSPF2 minimums. On top of the building codes, many cities apply zoning standards — setbacks and property-line noise limits — to outdoor units in side yards. Fees, forms, and which inspections the city actually runs are set locally — confirm with the building department.

For deeper background that isn't Los Angeles-specific, see the statewide mini-split installation guide.

Typically needs a permit

Mini-split installation itself triggers a permit in nearly every California jurisdiction, Los Angeles included. Los Angeles-specific variations are confirmed with the issuing department above.

Usually doesn't (general norm)

Plug-in portable air conditioners and window units
Routine service on an existing permitted system — cleaning filters and coils, clearing condensate
Replacing a remote or wall controller

Documents & plans generally required

Mechanical and electrical permit application (many cities issue a combined HVAC install/changeout permit)
Contractor license and city business registration
Equipment cut sheets for the indoor and outdoor units (SEER2/HSPF2 ratings, listing)
Circuit detail — dedicated circuit size, disconnect at the outdoor unit, and panel capacity (a load calc when capacity is tight)
Line-set routing and penetration-sealing detail
Condensate-termination detail for the indoor heads
Energy-compliance form (CF1R-ALT) where the city requires it for the alteration
Outdoor-unit placement showing clearances — some cities also apply setback and property-line noise standards (verify locally)

Common reasons mini-split installation applications get bounced

Code-rooted patterns across California — not a Los Angeles-specific rejection rate.

No dedicated circuit shown, or no disconnect within sight of the outdoor unit
Equipment below current federal minimum efficiency (SEER2/HSPF2) on the cut sheet
Condensate from indoor heads terminating to an unapproved location
Missing energy-compliance paperwork where the city requires a CF1R-ALT for the alteration
A panel without capacity for the new circuit and no load calculation provided
Outdoor unit placed in a required setback, or too close to openings or the property line where local standards apply

The inspection sequence

A typical order — the number of stops and exact sequence vary by jurisdiction and scope.

1Rough inspection if the line set, condensate line, or wiring is concealed in walls before cover
2Final inspection with the units mounted, circuit and disconnect complete, condensate terminated, and the system operating

Licensing — who can pull it

Mini-split installation in California is generally performed by a C-20 (HVAC) licensed contractor; the line-voltage circuit is C-10 (Electrical) work, and many shops hold both classifications or sub the circuit. A B (General Building) contractor may pull within a larger project under CSLB rules. The contractor doing the work typically pulls the permit.

Other verified Los Angeles notes

PermitLA handles express permits — simple construction projects that do not require plan review (per LADBS's Express Permit Eligibility list). For projects that need plan check, file through ePlanLA.
verified May 22, 2026 · source
Both PermitLA and ePlanLA require an Angeleno account — the single sign-on used across LA City services (Bureau of Engineering, City Planning, LADBS). Contractors must also have a current City Business Tax Registration and a CSLB license matching the work.
verified May 22, 2026 · source
In-person service is by appointment at any of LADBS's Development Services Centers: Metropolitan (downtown), Van Nuys, West LA, and San Pedro. The same online accounts work across all four offices.
verified May 22, 2026 · source
Fees are calculated from a building-permit valuation table plus per-trade fee tables (electrical, plumbing, mechanical, grading, fire sprinkler), with the LADBS Permit Fee Calculator providing project-specific estimates before filing.
verified May 22, 2026 · source

Frequently asked questions

Do I really need a permit for a single-zone mini-split?

Generally yes. A mini-split is a permanently wired heat pump with refrigerant lines, condensate, and a new dedicated circuit — permitted mechanical and electrical work in essentially every California city. Only plug-in portable and window units fall outside permitting.

Does a mini-split need HERS testing?

Ductless systems avoid the duct-leakage testing that ducted changeouts trigger under Title 24 — part of their appeal. Energy-compliance paperwork (CF1R-ALT) can still be required for the alteration, and a ducted mini-split air handler is treated like any ducted system. The exact form set depends on scope and climate zone — confirm what the city expects.

Can the outdoor unit go anywhere?

No — it needs the manufacturer's listed clearances, a disconnect within sight, and compliant condensate routing, and many California cities additionally apply zoning standards to equipment in side yards: setbacks and noise limits measured at the property line. That layer is local, so confirm placement rules with the city before committing the location.

Is a multi-zone system a different permit?

Usually the same permit with more scope — more heads mean more penetrations, more condensate terminations, and a larger or additional circuit. Panel capacity and the load calculation get more scrutiny as connected tonnage grows, which is where multi-zone applications most often pick up corrections.

Other jobs in Los Angeles

AC changeout Battery storage EV charger install All Los Angeles permits All California jobs

Want getPermit to map Los Angeles in depth?

Join the waitlist with your city and trade. We prioritize the jurisdictions our early users actually work in — and we'll never invent fees or timelines we haven't verified.

Join the waitlist