What does getPermit actually do?

getPermit reads your job details and tells you what a California city expects before you file: which permits the work triggers, the documents and plans you'll need, the fees to budget for, and the common reasons applications in that jurisdiction get bounced back. It produces a clear checklist you can act on. It does not submit to the city for you — you (or your permit person) stay in control of what gets filed.

Is there a human involved, or is it just AI?

Both. The AI does the research and drafts the assessment and checklist; an experienced permit coordinator reviews and approves it before it's treated as authoritative. The human check is the point — it's how we keep it trustworthy in a process where a wrong filing has real consequences.

Which cities do you cover?

We're starting deep in California rather than shallow everywhere. For a city we haven't fully mapped yet, we'll give you accurate general California guidance and point you to that city's official building department — and you can join the waitlist to be notified when we cover it in depth. We will not invent city-specific fees or timelines we haven't verified.

Solo electricians, plumbers, and HVAC contractors, and small general contractors who don't have a dedicated permit department and lose billable hours to permit admin.

How much does it cost?

It's pre-launch. Join the waitlist and you'll get founder pricing, your jurisdiction prioritized, and a direct line to the team. No spam, no credit card.

We're onboarding a first set of California contractors. Join the waitlist with your city and trade so we can prioritize the jurisdictions our early users actually work in.

Electrical panel upgrade permits in Unincorporated Los Angeles County, CA

General California guidance last updated May 22, 2026 · Unincorporated Los Angeles County data fully re-verified September 13, 2026

What electrical contractors need to know about pulling a electrical panel upgrade permit in Unincorporated Los Angeles County.

Short answer

In California, an electrical service or panel upgrade always needs an electrical permit and an inspection, and almost always requires utility coordination for the temporary disconnect. It is pulled by a licensed C-10 contractor under the California Electrical Code (Title 24, Part 3). Common drivers: EV chargers, heat pumps, solar/battery, ADUs, and replacing legacy/recalled panels (Federal Pacific, Zinsco, Pushmatic).

Unincorporated Los Angeles County accepts submittal through the EPIC-LA (Electronic Permitting and Inspections for the County of Los Angeles) and has adopted the 2026 County of Los Angeles Building Code (Title 26), adopting the 2025 California Building Code with County amendments. Fee details and sources are below.

Unincorporated Los Angeles County permit data

Sourced from public Los Angeles County documents — every field carries the source URL and verification date.

Permit portal

EPIC-LA (Electronic Permitting and Inspections for the County of Los Angeles)

verified Sep 13, 2026 · source · Building and Safety's online portal for the unincorporated areas: submit plans, specifications, and supporting documents for review and approval, pay permit fees, and apply for a permit. Contract cities use the separate Building and Safety Online Plan Check System (BSOP)

Adopted code edition

2026 County of Los Angeles Building Code (Title 26), adopting the 2025 California Building Code with County amendments

verified Sep 13, 2026 · source · Title 26 Sec. 100 adopts the 2025 California Building Code by reference, except as changed or modified in Title 26 (Ord. 2025-0047). Per Public Works' codes page, the 2026 County codes took effect January 1, 2026 for projects with an application date on or after that date — https://pw.lacounty.gov/building-and-safety/general

Fee schedule

Building and Safety fee schedules (County section, 2026-27) — building permit fees effective July 1, 2026 in unincorporated Los Angeles County

verified Sep 13, 2026 · source · The County's Building Code Fee Schedule (Title 26) PDF sets building permit fees in the unincorporated territory effective July 1, 2026; the 2026-2027 County public notice announces a 3.4% increase effective July 1, 2026 — https://pw.lacounty.gov/bsd/lib/fp/fees/County/2026-2027%20County%20Public%20Notice.pdf. Electrical, mechanical, plumbing, grading, and valuation tables are listed on the same index page

Los Angeles County Public Works — Building and Safety Division →All verified Unincorporated Los Angeles County data →

The general picture in California

A panel upgrade changes the building's electrical service — bumping the amperage (typically 100A → 200A, sometimes 225/400A), replacing the panel and meter, and often re-pulling the service lateral or mast. Because the work touches utility infrastructure and the main overcurrent device, it requires an electrical permit, a load calculation, a single-line diagram, and coordination with the utility for power-cut and reconnect. Grounding and bonding must meet the current code cycle (often a new ground-rod system in addition to the UFER), and AFCI/GFCI updates may be required on circuits being touched or extended.

For deeper background that isn't Unincorporated Los Angeles County-specific, see the statewide electrical panel upgrade guide.

Typically needs a permit

Electrical panel upgrade itself triggers a permit in nearly every California jurisdiction, Unincorporated Los Angeles County included. Unincorporated Los Angeles County-specific variations are confirmed with the issuing department above.

Usually doesn't (general norm)

Replacing a single breaker for one of the same type and rating
Tightening lugs or replacing a feeder bus cover (maintenance, not modification)
Re-labeling the panel directory

Documents & plans generally required

Electrical permit application
Contractor license and city business registration
Load calculation per NEC Article 220 (existing load + new loads)
Single-line diagram showing the new service size, meter, panel, main breaker, and grounding-electrode system
Site plan with panel/meter location and the service drop or lateral route
Cut sheet for the new panel (listing, AIC rating, bus rating, number of spaces)
Utility coordination forms (PG&E, SCE, LADWP, SDG&E — varies by service area)

Common reasons electrical panel upgrade applications get bounced

Code-rooted patterns across California — not a Unincorporated Los Angeles County-specific rejection rate.

Load calculation missing, incomplete, or not matching the proposed service size
No single-line diagram, or the diagram doesn't reflect the proposed work
Grounding/bonding details missing (UFER + supplemental ground rods, bonding jumpers)
AIC rating of the new equipment not coordinated with the utility's available fault current
Service-conductor sizing not matching the new main breaker
Working clearances around the panel not shown (NEC 110.26)

The inspection sequence

A typical order — the number of stops and exact sequence vary by jurisdiction and scope.

1Rough/service inspection before energization, with the panel set and grounding visible
2Utility coordination for temporary disconnect, meter pull, and reconnect
3Final inspection with the panel labeled, all circuits identified, and the service energized

Licensing — who can pull it

Panel and service upgrades in California are performed by a C-10 (Electrical) licensed contractor; a B (General Building) contractor may pull within a larger project under CSLB rules. The licensed contractor pulling the permit typically also coordinates the utility cut and reconnect.

Other verified Unincorporated Los Angeles County notes

Los Angeles County Building and Safety, managed by LA County Public Works, provides building services to unincorporated communities at the Public Works headquarters (900 S. Fremont Avenue, Alhambra, CA 91803) and at Building and Safety District Offices.
verified Sep 13, 2026 · source
The Public Works Service Locator (https://pw.lacounty.gov/general/servicelocator/) shows the Building and Safety office that serves an address; if a County Building and Safety office does not serve the property, it shows the jurisdiction that does.
verified Sep 13, 2026 · source
A permit can only be issued to a contractor with the appropriate license(s), to the property owner in certain cases, or to an authorized agent representing one of these two permittees.
verified Sep 13, 2026 · source
Inspections for permits in the unincorporated areas are requested online through the permit holder's EPIC-LA account, at least 24 hours in advance.
verified Sep 13, 2026 · source
Express Permits — for standalone work or projects whose building permit is already issued — are submitted online only through EPIC-LA; once all required fees are paid, the permit is issued automatically.
verified Sep 13, 2026 · source
Wildfire rebuilds: projects to repair, restore, demolish, or replace residential structures substantially damaged or destroyed in the 2025 Eaton and Palisades wildfires may comply with the 2022 Building Standards Code as adopted by the County, provided the plans meet the 2025 fire and public safety requirements and National Flood Insurance Program minimum elevation requirements (Title 26 Sec. 100).
verified Sep 13, 2026 · source
Wildfire rebuilds: LA County runs One-Stop Permit Centers in the Eaton and Palisades fire burn areas — Altadena (464 W Woodbury Rd. Suite 210, Altadena, CA 91001) and Calabasas (27001 Agoura Road, Suite 250) — and offers free virtual rebuild appointments for County unincorporated-area residents.
verified Sep 13, 2026 · source
Wildfire rebuilds: the Board of Supervisors approved deferring and refunding fees for qualifying owners rebuilding single-family homes in unincorporated Los Angeles County after the Eaton and Palisades wildfires; applicants must show they both owned and lived on the property before January 7, 2025, and the fees will not be collected from property owners.
verified Sep 13, 2026 · source

Frequently asked questions

When does California require a panel upgrade?

When the load calculation shows the existing service can't carry the new connected load — most often triggered by EV chargers, heat pumps, solar/battery, ADUs, or replacing a recalled panel brand (Federal Pacific, Zinsco). The upgrade is permitted as a single project even when it bundles multiple drivers.

Do I need to coordinate with the utility?

Yes — service upgrades require utility coordination for the temporary disconnect, meter pull, and reconnect. PG&E, SCE, LADWP, and SDG&E each have their own application and lead time; the contractor typically handles this in parallel with the city permit.

Can I keep the same panel location?

Generally yes, if the location still meets NEC 110.26 working clearances and the meter remains accessible to the utility. Moving the panel can simplify the install or be required when the existing location is non-compliant.

Does the panel upgrade trigger AFCI/GFCI updates on existing circuits?

Generally only the circuits being touched, extended, or replaced have to meet the current code cycle's AFCI/GFCI rules — existing circuits left in place are usually grandfathered. Some jurisdictions are stricter on this; confirm with the city.

Other jobs in Unincorporated Los Angeles County

AC changeout Battery storage EV charger install All Unincorporated Los Angeles County permits All California jobs

Want getPermit to map Unincorporated Los Angeles County in depth?

Join the waitlist with your city and trade. We prioritize the jurisdictions our early users actually work in — and we'll never invent fees or timelines we haven't verified.

Join the waitlist