What does getPermit actually do?

getPermit reads your job details and tells you what a California city expects before you file: which permits the work triggers, the documents and plans you'll need, the fees to budget for, and the common reasons applications in that jurisdiction get bounced back. It produces a clear checklist you can act on. It does not submit to the city for you — you (or your permit person) stay in control of what gets filed.

Is there a human involved, or is it just AI?

Both. The AI does the research and drafts the assessment and checklist; an experienced permit coordinator reviews and approves it before it's treated as authoritative. The human check is the point — it's how we keep it trustworthy in a process where a wrong filing has real consequences.

Which cities do you cover?

We're starting deep in California rather than shallow everywhere. For a city we haven't fully mapped yet, we'll give you accurate general California guidance and point you to that city's official building department — and you can join the waitlist to be notified when we cover it in depth. We will not invent city-specific fees or timelines we haven't verified.

Solo electricians, plumbers, and HVAC contractors, and small general contractors who don't have a dedicated permit department and lose billable hours to permit admin.

How much does it cost?

It's pre-launch. Join the waitlist and you'll get founder pricing, your jurisdiction prioritized, and a direct line to the team. No spam, no credit card.

We're onboarding a first set of California contractors. Join the waitlist with your city and trade so we can prioritize the jurisdictions our early users actually work in.

Gas line permits in Texas

Last updated September 13, 2026

Early Texas guides. getPermit is California-first — these pages share what we've verified in Texas so far, and they don't mean getPermit covers Texas yet. Join the waitlist with your city to tell us where to go deeper.

A plain-English starting point for plumbing contractors. This is general Texas guidance — fees, forms, and timelines are set by each city.

Short answer

New or extended gas piping generally needs a permit in Texas cities, pulled by a TSBPE-licensed Responsible Master Plumber — gas piping is plumbing under Texas law. Before gas service comes back, the city tests and releases the line: Dallas requires a 3 psig pressure test held at least 15 minutes and witnessed by a City inspector before Atmos Energy restores service.

The general picture

Gas work in Texas is plumbing work, so a licensed master plumber pulls the permit, and the city controls when gas flows again. In the Dallas–Fort Worth cities we've checked, the key step is the test and release: Dallas requires a pressure test witnessed by a City inspector before Atmos Energy restores service, and when gas service has been lost in Arlington, the City releases it to Atmos only after a permit and a passed inspection. See the verified notes for Dallas and Arlington.

Typically needs a permit

Adding or extending gas piping to a range, dryer, outdoor kitchen, fireplace, pool heater, or generator, and altering existing piping. Gas service stays off until the city approves the piping.

Usually doesn't (general norm)

Relighting a pilot or servicing an appliance without touching the gas piping

Documents & plans generally required

Plumbing (gas) permit application
Responsible Master Plumber license number and city registration
Piping layout with pipe sizes, lengths, and material
Input rating for every appliance on the system
Pipe sizing for the total connected load

Common reasons gas line applications get bounced

Code-rooted patterns across Texas — not a city-specific rejection rate.

Pressure test not holding at the required pressure and duration
Pipe sized for the new appliance but not the whole system
Piping covered or backfilled before inspection
Gas turned on before the city's release
Plumber not registered with the city where registration is required

The inspection sequence

A typical order — the number of stops and exact sequence vary by jurisdiction and scope.

1Rough inspection and pressure test before the piping is covered
2In Dallas, a 3 psig test held at least 15 minutes, witnessed by a City plumbing inspector
3City release to the gas utility, which restores or connects service

Licensing — who can pull it

Gas piping in Texas is plumbing work done by a TSBPE-licensed plumber, with a Responsible Master Plumber pulling the permit. Propane (LP-gas) work is regulated by the Railroad Commission of Texas; plumbers and ACR contractors can register for an exemption from its license.

How this works in your Texas city

Cities marked have verified local data — portal, fee schedule, adopted code edition, and local permit notes sourced from public city and county documents. Every city page links to its official building department.

Dallas Fort Worth Arlington Plano

Frequently asked questions

Do I need a permit to run a gas line in Texas?

Generally yes. Gas piping is plumbing under Texas law, and Dallas, Fort Worth, and Plano require permits for plumbing work; Dallas also publishes its gas test procedure.

How is a gas line tested in Dallas?

At 3 psig for at least 15 minutes, witnessed by a City plumbing inspector. After the City's release, Atmos Energy restores or connects service.

What about propane?

Propane (LP-gas) systems fall under the Railroad Commission of Texas. Plumbers and ACR contractors can register with the Commission for an exemption from its LP-gas license.

Other common jobs

AC changeout Battery storage EV charger install All jobs All Texas guides

Want getPermit to map your city in depth?

Join the waitlist with your city and trade. We prioritize the jurisdictions our early users actually work in — and we'll never invent fees or timelines we haven't verified.

Join the waitlist